Portable X-ray Diagnosising system

X-ray machine Product Introduction: Portable medical X-ray diagnostician system is a new generation product which developed based on the first generation –portable visual X-ray machine, and specially designed for the public medical industry, it has all the merits of the first generation, in addition, it can change the skeleton image into vision signal and digital image signal through digital/analog conversion and noise reduction: you can record, transfer, conserve and handle these images at any time. In this way, this kind machine provides doctors with strong guarantee for their speedy and exact diagnosis. Portable medical X-ray diagnostician system is a kind of high-tech product which through great concentrative studies, it possesses several core techniques and patents, initiating in home and abroad, it mixed present advanced intensification technique of X-ray image, digital technology, noise reduction technique, software-exploit technique, this system maximum satisfied users’ requirements for digitization. The Instruction is Suitable for the Following Model Number: X-ray Leakage and Safety: The principal X-ray dose of the system is lower than 5 mR/h(which of national standard is less than 100Mr/h).In order to avoid X-ray damage, we have taken a series of close & effective measures to handle X-ray leakage, including the lead cover of X-ray source, the lead board of the intensifier edge, lead glass of the fluorescent, screen, collimator device and so on. So the leakage dose is very low, the user needn’t any protection.All the x-ray leakage dose of the machine’s vision in any direction is less than 5Mr/h, which is up to the safety and protection standard of the Health Department.Using Circumstance: 1. Geolocation altitude: 4000 meters below sea level. 2. Temperature: 5C----40C. 3. Relative humidity: below 95% 4. This system belongs to the kind of Class I equipment, the power source must be good grounded, if your plug base isn’t grounded, please draw out the ground cable from the machine to connect first. 5. Any violent vibration is not allowed during photographing. Basic Structure: Please check whether it includes all the needs: It should includes the mainframe, power source of the converter, wired remote touching switch, optical disc of the software , and the instruction, the computer is selective The diagram of our X-ray diagnostician system is as follows: Components Explanation in the Diagram: 1: X-ray source; 2:body frame; 3:bottom; 4:handle; 5: earth wire hole;6:power interface; 7:the interface of wired remote touching switch;8: the precaution cover of x-ray input port(demountable);9:image intensifier storehouse;1.:digitalization storehouse;11.USB interface, connect with the computer with installment driver and managing software through the USB cable(Note: the USB interface is 2.0 edition );12:wired remote touching switch and plug(connect with 7);13: power supply box; 14:220Vplug; 15: power supply box output(connect to 6 on the mainframe) Assert: For constant renovation, the real products may different in specification and scale, but the basic structure is alike. Mainframe Installation: After check your product, you would install the equipment first before you use it, you may need to dismantle and install it usually because it is a kind of portable machine. In order to avoid unnecessary damage, please be sure to operate it according to its instruction. First: Installation of dismantled protective over 8. Stand the mainframe steadily on your desk, put the intensifier by your side, and plug the tailspin according to related mark(Note: the triangle location pin and corresponding slot); then make the protective cover aligned with the slot with the fitting mark(location pin),ensure all the three location pins in the gap of protective cover, pull the protective cover to the end, and screw it down from inverted hour; When dismantle, your pose is the same with that when you install it , spin the protective cover form clockwise to the end, push the protective cover to make the location pin separate from gap, then put it well on the forth pad of its suitcase, close the suitcase in order to be convenient for carry, transport and storage. Second: Put one end of power supply output plug 14 aim at and insert into plug 13, Put power supply output line 15 aim at and insert into the interface of mainframe 6, insert the twin core plug 12 of touching switch into the interface of mainframe 7, then screw the digitalization storehouse10 from clockwise, until it is aligned with the marked on the image intensifier storehouse 9, connect USB cable with you PC USB and the USB interface11 respectively. Third: Connect one end of 220V plug 14 to 220V/50Hz intercourse Power Supply, switch the button of the power supply box to 75V (60V is for BXX50D/A), switch on power supply, then you can find the green light is shine on the power source must be good grounded); if your plug base isn’t grounded, please draw out the ground cable 5 from the machine to connect. Four: Start your PC, if this is your first time to use it, you need to install driver system, therapy operation and management software (vide infra “Driver & Software Installation”), concrete using methods, please refer to “inspect part”.